| T.R | Title | User | Personal
Name | Date | Lines |
|---|
| 1117.1 | how about sim callout | AFW3::MAZUR | | Wed Feb 26 1997 13:04 | 8 |
| Have you tried running SIM CALLOUT on this memory? Do you know about that
console/diag feature. If you did try it, did it not find the problem?
It will call out the location of the bad sim.
>>> Set sim_callout On
>>> init
|
| 1117.2 | >>> all internal tests are ok <<< | COLES1::LONZECK | | Wed Feb 26 1997 15:55 | 28 |
| Hello,
i try the Simm_callout, but i get no result.
The system tells me that all is fine.
Test MS7cc works also without errors.
The Problem is described also in this note: 1109.
TLASER FW V4.1-6
additional info: System crash varios between 1h and 3-4 Day's.
In case of systemcrash only Pwr / reset works, because the Console
crashs and loop. (see in this Note entry 1109)
All internal A8400 Diags runs (test for 3-8h) without any error.
If a error detected the System hung, no <CNTR> P...... work.
Also here only a Power reset get me the console back and no
errorinformation are stored in any register.
For the defektive memory i get from decevent the information that there
is a problem with bank 1.
Installed are two MS7CC-FA (2GB) Modules at the time of crash with 4
way interleaving.
My question only, also for future, what does 'dia' (decevent V2.2) mean
with bank 1 ?
Which SIMM's (Jxx) are Bank1, Bank2..........
regards, Uwe
|
| 1117.3 | | DANGER::HARTWELL | | Wed Feb 26 1997 19:09 | 8 |
| You have an intermittent bus protocol problem that could be due
to any number of issues. Since you have identified the offending
module, you should be all set. Nothing tests the system better
than the OS with either specialized tests or customer Apps.
/Dave
|
| 1117.4 | Here is a simm/bank chart | HARMNY::PREISIG | | Mon Mar 03 1997 13:57 | 21 |
|
Here is a chart that answers your original question (1117.0)
MS7CC-GA SIMM/BANK CHART
Bank 0 Bank 1 Bank 2 Bank 3
------ ------ ------ ------
J2 J3 J8 J9
J4 J5 J10 J11
J6 J7 J12 J13
J14 J15 J22 J23
J16 J17 J24 J25
J18 J19 J26 J27
J20 J21 J32 J33
J28 J29 J34 J35
J30 J31 J36 J37
|
| 1117.5 | MS7CC-FA Layout the same ?? | COLES1::LONZECK | | Mon Mar 03 1997 17:19 | 6 |
| Hello,
thanks for the Information about the MS7CC-GA (4GB Memory Module)
Banklayout.
Is the Banklayout for the MS7cc-FA (2GB Memory Module) the same ???
|
| 1117.6 | Layout is not the same | TARKIN::HALL | | Tue Mar 04 1997 13:01 | 2 |
| No the simm layout is not the same. The MS7CC-FA (2GB) only has 2 banks
per module. Where as the MS7CC-GA (4GB) has 4 banks per module.
|
| 1117.7 | Please provide Chart for MS7CC-FA | COLES1::SIEK | | Wed Mar 05 1997 06:55 | 10 |
| Hi!
Is there nobody out there, that can provide the SIMM/BANK layout
of the MS7CC-FA module as done in .4???
We already had a lot of trouble with these modules, and as you can
see in this entry, not all the problems can be found by setting
SIMM_CALLOUT to on.
Herbert
|
| 1117.8 | look in the PFMS... | WONDER::MUZZI | | Wed Mar 05 1997 11:37 | 11 |
|
The simm/bank callout is in the PFMS for both the 128/256/512/1gb and
the 2gb boards, and the callout is correct in DECevent. I'm not sure if
the 4gb board simm/bank has made it into the new PFMS but it should be
there shortly...and the DEVevent that will ship with the new 4gb boards
has the correct simm callout.
-Mark-
|
| 1117.9 | Not the answer of my question ! | COLES1::LONZECK | | Thu Mar 06 1997 06:14 | 15 |
| Hello Mark,
thats not the right answer.
What i need is: MS7CC-xx E2035-AA Bank1 = SIMM Jxx ; Jyy ; Jzz
Bank2 = .......
....
MS7CC-xx E2036-AA Bank1 = SIMM Jxx ; Jyy ; Jzz
Bank2 ....
....
I don't have any information about the PFMS.
//Uwe
|