| T.R | Title | User | Personal
Name | Date | Lines |
|---|
| 3298.1 | try installing again | TOOK::ECKHARDT | | Mon Jul 06 1992 20:06 | 16 |
|
Hello Peter,
Try installing the latest version of DECmcc BMS V1.2.0 on
your system. I justed restored the kit from the mccbmsv120.tar
file and installed DEC Threads and the BMS kit successfully.
Remember to delete (setld -d) any old version of the DECmcc BMS
kit and any old DEC Threads kit (CMA or THRBASE kit) prior to
the installation. Although the THRBASE111 kit will install on top
of old DEC Threads kits, you should still delete the old versions
of DEC Threads or the DECmcc BMS kit will not allow its installation
to continue.
- Raina
|
| 3298.2 | Still having problems!! | PJWL::LAMB | Peter Lamb - GSG Santa Clara MAIL=MUTTON::LAMB | Tue Jul 07 1992 03:33 | 33 |
| I just used FTSV to copy the latest kit down from MCCNIX
and am still having the exact same problem. Could FTSV
be munging the file??
I am going to try dcp'ing the file directly again to see
whether that makes any difference.
Regards,
Peter Lamb
Starting installation of
DECthreads Base Services for Ultrix (RISC) (THRBASE111).
DECthreads Multithreading Services for Ultrix (RISC) THRBASE111 (THRBASE111)
Copying from /usr/kits (disk)
./usr/kits/THRBASE111/include: Not a directory
tar: Directory checksum error, possible file name:
/*
* %W% (DEC OSF/1) %G%
*/
/*
* Copyright (c) 1990, 1992 by
* Digital Equipment Corporation,
Broken pipe
setld:
File copy to system disk failed.
Subset THRBASE111 may not have been installed properly on your system
but the rest of the installation will continue.
|
| 3298.3 | Try ULTRIX -> ULTRIX | TOOK::MINTZ | Erik Mintz, dtn 226-5033 | Tue Jul 07 1992 04:05 | 5 |
| People have reported mixed results when copying ULTRIX kits
through a VMS system. It is quite likely that that is what is
causing your checksum error.
-- Erik
|
| 3298.4 | direct copy same problem | PJWL::LAMB | Peter Lamb - GSG Santa Clara MAIL=MUTTON::LAMB | Tue Jul 07 1992 04:57 | 7 |
| Nope! I just tried it again with
dcp -iv mccnix::~ftp/pub/mccbmsv120.tar .
and am still having the same exact problem!!
Peter
|
| 3298.5 | Kits are known to work | RACER::dave | Ahh, but fortunately, I have the key to escape reality. | Tue Jul 07 1992 16:46 | 5 |
| I copied all of the kits last night and installed them with no problem,
so the kits are known to be good. The last time I had problems like this
was with a bad block on my disk.
DRL
|
| 3298.6 | Still having problems | MUTTON::LAMB | Peter Lamb - GSG Santa Clara | Sun Jul 12 1992 21:32 | 16 |
| I guess I have a lot of bad blocks!!
I was finally able to get DECmcc ultrix installed on one of my systems...
Bob Harcopus (sp?) pointed me to another kit that I was able to copy down
the odd thing is that the network link was broken two thirds of the way
through copying this kit such that it was uncomplete however, I was able
to use this kit to install threads. I am now trying to install DECmcc on
another Ultrix system and am having the exact same problem... After my
link went down I re-copied the entire kit again and this is the kit I used
to install evertyhing except threads but when I copy this kit to another
system I get the exact same error.
Regards,
Peter Lamb
|
| 3298.7 | Problem solved | PJWL::LAMB | Peter Lamb - GSG Santa Clara MAIL=MUTTON::LAMB | Tue Jul 14 1992 14:31 | 17 |
| After much frustration and a great deal of assistance from Jim
Dougherty we finally figured it out!! My problems were two fold...
1) Once a setld is corrupted you have to setld -d before
you attempt to reinstall it
2) The threads kit uses /usr/kits so if you put the .tar
file there and un-tar it you will get a corruption
problem since the installation procedure trys to create
a directory in /usr/kits THR111 that is the same name as
a file tar created.
Thanks again Jim for you patience!!
Regards,
Peter Lamb
|