| Folks,
I tried upgrading the firmware and it went something like this. The
following is the guideline I used during the upgrade with info embedded
from the UCX$TFTP_STARTUP.LOG;11 file.
Upgrading firmware on a Gigaswitch
Configuration: VAX7810, DEMFA, VMS 6.2 or greater, UCX 4.0, DECndu
1.0
1. Install UCX - @sys$update:ucx$cleanup.com
@sys$update:vmsinstal * dka100:[ucx040.kit]
2. Get host systems's IP address and NAME ( 128.251.20.70 decv01)
3. Configure UCX - @sys$manager:ucx$config
(a) core
(b) interface - choose circuit, system NAME and
IP address, make sure the gigaswitch submask is
the same as this system. $ ucx show interface
(c) server components - enable TFTP and BOOTP
(d) shutdown UCX
(e) startup UCX
4. $ ucx show service - look for TFTP and BOOTP
5. $ show system - look for ucx$bootp
6. Get vaxbinjun96 - openvms VAX software product library disk#6
AG-PR57T-RE
7. Install DECndu - [dcf011] is the directory that has DECndu
@sys$update:vmsinstal nduplus dka100:[dcf011.kit]
8. Check to see if tcp/ip is running on the circuit you have plugged
into the
gigaswitch. $ anal/system show lan/full, if not rerun ucx$config
again
9. $ ucx show config snmp - should be public
10. Insure all firmware files are located in mom$load:
clk-30.rsx
fg4-31.rsx
scp-31.ftp
sbb-31.ftp
GSSCP_22.TFT
11. At the gigaswitch
(a) set IP adrs - 5.2 128.251.20.61 0.0.0.0
subnet mask 255.255.0.0
(b) show box configuration - get lowest lan address or
get it off the clock card, it will be the SA adrs.
read write community string password
"08002BB31380"
(c) show slot configuration
scp slot 4
flg 5
flg 6
clk 7
(d) show priviledged ports - make them all
(e) show bootserver ports - make them all
12. $ ucx ping 128.251.20.61 - ping the switch from the vax
13. The order of loading firmware is line cards, clock and scp
however our problem is unique.
$ DOWNLOAD SHOW DEVICE 128.251.20.61/FORCE=GIGDESCR/MODULE=4
********************************************************************************
My problem begins here. As a result of the next command
the load process hung trying to tranfer the data and this is a log
taken for sys$sysdevice:[ucx$tftp].
$ ty UCX$TFTP_STARTUP.LOG;11
$! login.com for DEC TCP/IP Services Auxiliary service
$ !
$ !
$ ! Copyright (c) Digital Equipment Corporation, 1990, 1992
$ ! All Rights Reserved. Unpublished rights reserved
$ ! under the copyright laws of the United States.
$ !
$ ! The software contained on this media is proprietary
$ ! to and embodies the confidential technology of
$ ! Digital Equipment Corporation. Possession, use,
$ ! duplication or dissemination of the software and
$ ! media is authorized only pursuant to a valid written
$ ! license from Digital Equipment Corporation.
$ !
$ ! RESTRICTED RIGHTS LEGEND Use, duplication, or
$ ! disclosure by the U.S. Government is subject to
$ ! restrictions as set forth in Subparagraph (c)(1)(ii)
$ ! of DFARS 252.227-7013, or in FAR 52.227-19, as
$ ! applicable.
$ !+
$ !
$ SET PROCESS /PRIV=(NOALL,NETMBX,TMPMBX)
$ SET DEFAULT UCX$TFTP_ROOT:[000000]
$ RUN SYS$SYSTEM:UCX$TFTP.EXE
Feb 2 14:14:28 17664 Recv RRQ File=/homes/milldf/x0abf16.prm
Mode=octet
%UCX-W-TFTP_OPNFILERR, 2-FEB-1997 14:14:28.65 Can't open file
/homes/milldf/x0a
bf16.prm for client with address 128.251.251.16
-RMS-F-SYN, file specification syntax error
Feb 2 14:14:28 17664 Send ERROR 1 Can't open file for read/write
Feb 2 14:17:33 17664 Recv RRQ File=XYPLEX/x0173db.prm Mode=octet
%UCX-W-TFTP_OPNFILERR, 2-FEB-1997 14:17:33.92 Can't open file
XYPLEX/x0173db.pr
m for client with address 128.251.250.83
-RMS-F-SYN, file specification syntax error
Feb 2 14:17:33 17664 Send ERROR 1 Can't open file for read/write
$
The firmware never did get loaded and we as in myself and the CSC
made every attemp to get it installed. We upgraded UCX to version 4.1
ECO1 with no success.
****************************************************************************
* $ download load /module=4/pass="08002bb31380" 128.251.20.61
* /force=gigaswitch -
* _$ mom$load:gsscp_22.tft
********************************************************************************
In another attemp, the log looked like this, I've edited it to
remove some of the repetition.
$! login.com for DEC TCP/IP Services Auxiliary service
$ !
$ !
$ ! Copyright (c) Digital Equipment Corporation, 1990, 1992
$ ! All Rights Reserved. Unpublished rights reserved
$ ! under the copyright laws of the United States.
$ !
$ ! The software contained on this media is proprietary
$ ! to and embodies the confidential technology of
$ ! Digital Equipment Corporation. Possession, use,
$ ! duplication or dissemination of the software and
$ ! media is authorized only pursuant to a valid written
$ ! license from Digital Equipment Corporation.
$ !
$ ! RESTRICTED RIGHTS LEGEND Use, duplication, or
$ ! disclosure by the U.S. Government is subject to
$ ! restrictions as set forth in Subparagraph (c)(1)(ii)
$ ! of DFARS 252.227-7013, or in FAR 52.227-19, as
$ ! applicable.
$ !+
$ !
$ SET PROCESS /PRIV=(NOALL,NETMBX,TMPMBX)
$ SET DEFAULT UCX$TFTP_ROOT:[000000]
$ RUN SYS$SYSTEM:UCX$TFTP.EXE
Feb 2 13:45:28 17664 Recv RRQ File=/homes/milldf/x0abf16.prm
Mode=octet
%UCX-W-TFTP_OPNFILERR, 2-FEB-1997 13:45:28.67 Can't open file
/homes/milldf/x0
-RMS-F-SYN, file specification syntax error
Feb 2 13:45:28 17664 Send ERROR 1 Can't open file for read/write
Feb 2 13:48:33 17664 Recv RRQ File=XYPLEX/x0173db.prm Mode=octet
%UCX-W-TFTP_OPNFILERR, 2-FEB-1997 13:48:33.89 Can't open file
XYPLEX/x0173db.p
-RMS-F-SYN, file specification syntax error
Feb 2 13:48:33 17664 Send ERROR 1 Can't open file for read/write
Feb 2 13:55:29 17664 Recv RRQ File=MOM$LOAD:GSSCP_22.TFT Mode=octet
%UCX-I-TFTP_RRQ, 2-FEB-1997 13:55:29.96 Read request for file
MOM$LOAD:GSSCP_2
8708 Init Task 8eec0 First 8eec0 Next 0 Sock 256 File 123084
8708 Send DATA 1 Size 512
8708 Recv ACK 1
8708 Send DATA 2 Size 512
8708 Recv ACK 2
8708 Send DATA 3 Size 512
8708 Recv ACK 3
8708 Send DATA 4 Size 512
8708 Recv ACK 4
8708 Send DATA 5 Size 512
.
.
8708 Send DATA 2563 Size 512
8708 Recv ACK 2563
8708 Send DATA 2564 Size 512
8708 Recv ACK 2564
8708 Send DATA 2565 Size 512
8708 Recv ACK 2565
8708 Send DATA 2566 Size 512
8708 Recv ACK 2566
8708 Send DATA 2567 Size 512
8708 Clos File 123084
8708 Recv ACK 2566 Expected 2567
8708 Recv ACK 2567
8708 Send DATA 2568 Size 512
8708 Recv ACK 2568
8708 Send DATA 2569 Size 0
8708 Clos Sock 256
8708 Free Task 8eec0 First 8eec0 Next 0
Feb 2 14:00:00 17664 Recv RRQ File=x0abf02.prm Mode=octet
%UCX-W-TFTP_OPNFILERR, 2-FEB-1997 14:00:00.04 Can't open file
x0abf02.prm for
-RMS-E-FNF, file not found
Feb 2 14:00:00 17664 Send ERROR 1 Can't open file for read/write
The SCP file I was trying to load GSSCP_22.TFT is 2568 blocks.
****************************************************************************
$ DOWNLOAD SHOW DEVICE 128.251.20.61/FORCE=GIGDESCR/MODULE=6
$ download load /module=6/pass="08002bb31380" 128.251.20.61
/force=gigaswitch -
_$ mom$load:fg4-31.rsx
$ DOWNLOAD SHOW DEVICE 128.251.20.61/FORCE=GIGDESCR/MODULE=5
$ download load /module=5/pass="08002bb31380" 128.251.20.61
/force=gigaswitch -
_$ mom$load:fg4-31.rsx
$ DOWNLOAD SHOW DEVICE 128.251.20.61/FORCE=GIGDESCR/MODULE=7
$ download load /module=7/pass="08002bb31380" 128.251.20.61
/force=gigaswitch -
_$ mom$load:clk-30.rsx
Reboot switch
$ DOWNLOAD SHOW DEVICE 128.251.20.61/FORCE=GIGDESCR/MODULE=4
$ download load /module=4pass="08002bb31380" 128.251.20.61
/force=gigaswitch -
_$ mom$load:scp-31.ftp
$ download load /module=4pass="08002bb31380" 128.251.20.61
/force=gigaswitch -
_$ mom$load:sbb-31.ftp
Reboot switch
notes: How to get current images over the network
$ ftp gatekeeper.dec.com
anonymous
ftp> cd /pub/Digital/Gigaswitch
ftp> get README
ftp> get postscript files
ftp> bin
ftp> get images
ftp> bye
other locations: www.networks.digital.com
school::sonoma_rm:[sonoma_fw_rm.v22]
I really need some help (discussion) as to what I have done wrong.
Everyone seems to believe that this upgrade runs smoothly, please help.
regards,
Ernesto Buensuceso
MCS Dallas, Tx
|